環能瓦斯發電機組使用中遇到水溫升高的情況，是哪些原因造成的，作為燃?xì)獍l(fā)電機廠家，讓小編帶大家共同了解一下。

　　What are the causes of water temperature rise encountered during the use of the Huanneng gas generator set? As a gas generator manufacturer, let me take you to understand together.

　　、是陵油時間過早或過遲屬，影響燃燒過程，引起補燃期過長，使冷卻水接觸氣缸壁的時間相對延長，造成水溫過高，這個一般是根據反斯環能瓦斯發電機組的品牌不同，它的噴油時間不同，正常的發動機都不會存在這樣的問題，除非機器收過損傷。

　　If the oil injection time is too early or too late, it will affect the combustion process, cause a long afterburning period, and prolong the time for the cooling water to contact the cylinder wall, resulting in a high water temperature. This is generally due to the different brands of gas generators with different injection times, and normal engines will not have such problems unless the machine has been damaged.

　　二、是噴油量過大，造成混合氣過濃，緩燃期、補燃期相應延長，而使水溫過高。這個可能是由于突然加負載，或者突然加大油門造成

　　2、 It is due to excessive fuel injection that the mixture is too rich, resulting in a corresponding extension of the slow burn and afterburn periods, and causing the water temperature to be too high. This may be caused by sudden loading or sudden acceleration of the accelerator

　　三、是畸油器噴油壓力過高或過低，使燃油的噴射行程和霧化質量受到影響。噴油壓力過高，噴在燃燒室壁上的反斯環能瓦斯發電機組形成液態，不利于霧化險為夷噴油壓力低，霧化質量差。噴油器滴油使供油量加大，引起水溫過高，嚴重時使噴油器燃損。

　　3、 It is the high or low injection pressure of the fuel injector that affects the fuel injection stroke and atomization quality. The injection pressure is too high, and the anti sulfur ring energy gas generator unit sprayed on the combustion chamber wall forms a liquid state, which is not conducive to atomization. The injection pressure is low, and the atomization quality is poor. Dripping oil from the fuel injector increases the fuel supply, causing high water temperature and, in severe cases, fuel damage to the injector.

　　四、是配氣相位失準，使氣缸在壓縮終了時壓縮壓力降低;進氣不充分，排氣干凈，延長了緩燃期和補燃期，引起水溫過高。進氣系統堵塞也會使混合氣體過濃，發動機冒黑煙，動力下降，水溫過高。氣門和氣門座圈磨損，活塞和缸套磨損均使壓縮力降低，引起燃燒不良也使水溫過高，動力性能下降。

　　4、 It is the misalignment of the valve timing that causes the compression pressure of the cylinder to decrease at the end of compression; Insufficient intake and clean exhaust have prolonged the ignition delay and afterburning period, resulting in excessively high water temperature. Blockage in the intake system can also cause the mixture to become too rich, resulting in black smoke from the engine, decreased power, and excessively high water temperature. The wear of valves and valve seat rings, as well as the wear of pistons and cylinder liners, reduces compression force, causes poor combustion, and leads to high water temperature, resulting in decreased power performance.

　　五、是散熱器堵塞、水垢過多及風扇膠帶松弛等均會造成水溫過高。水泵壓力低，流量小，使冷卻液循環速度慳，從而造成水溫過高。需要定期清洗水箱，更換冷卻液六、是發動機內部零部件之間摩擦阻力大，潤滑條件不好，排氣管或消間器堵塞，發動機負荷過大等也會造成水溫過高的現象。檢查使用的潤滑油的油品及質量。

　　5、 Blockage of the radiator, excessive scale, and loose fan tape can all cause high water temperature. The low pressure and low flow rate of the water pump result in slow circulation of the coolant, leading to excessively high water temperature. Regular cleaning of the water tank and replacement of coolant are necessary. Additionally, high friction resistance between internal engine components, poor lubrication conditions, clogged exhaust pipes or dampers, and excessive engine load can also cause high water temperature. Check the quality and quality of the lubricating oil used.

　　本文由   環能瓦斯發電機組  友情奉獻.更多有關的知識請點擊  http://m.qmtg666.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Huaneng Gas Generator Unit For more related knowledge, please click http://m.qmtg666.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.